Hello forum xx
Most of you know I make videos. I would really like to have a cockbox in my bag of tricks
I'm sure there's a few of you out there that could point me to somewhere with instructions on how to build one xxxx
Cockbox
Moderators: Only Pumps, Richie, Jess, minni, sh03s, cumheels, Mrs.HB, redwedge, Heelexploder, german bootlover, heelbone, HighHeelFetish.org, Bound&Milked, Tamaris
-
- Posts: 679
- Joined: Fri Sep 01, 2017 6:30 am
- Contact:
-
- Posts: 2111
- Joined: Wed Sep 18, 2013 5:44 am
Re: Cockbox
I found a forum a few years ago that had a pretty good explanation but I can't seem to find it again. It was a CBT forum where they were discussing different design ideas. If you or a friend has some wood working experience then it wouldn't be that difficult. I made one out of 12" wide pine board. I used a hole saw to cut a hole in the middle and sanded the crap out of the sharp hole corners. Make sure to sand the leading edges of the board too. For the sides I used the same pine board. I got measurements of how high I needed it by laying flat on the floor. Remember to account for the thickness of the board in the measurement. I then measured for how wide to make it. When I put the three pieces together I used long deck screws and pre-drilled them. My board is not for standing on with full weight. If you want to do that then use 4x4 posts for the sides. There are some design ideas here that may help you out.
http://www.mistressdestiny.com/threads/ ... ox.426512/
http://www.mistressdestiny.com/threads/ ... ox.426512/
-
- Posts: 679
- Joined: Fri Sep 01, 2017 6:30 am
- Contact:
Re: Cockbox
Thank you for your help. I think I'll be able to get someone to build me one (or two)sandalfan1 wrote: ↑Tue Jun 26, 2018 4:15 am I found a forum a few years ago that had a pretty good explanation but I can't seem to find it again. It was a CBT forum where they were discussing different design ideas. If you or a friend has some wood working experience then it wouldn't be that difficult. I made one out of 12" wide pine board. I used a hole saw to cut a hole in the middle and sanded the crap out of the sharp hole corners. Make sure to sand the leading edges of the board too. For the sides I used the same pine board. I got measurements of how high I needed it by laying flat on the floor. Remember to account for the thickness of the board in the measurement. I then measured for how wide to make it. When I put the three pieces together I used long deck screws and pre-drilled them. My board is not for standing on with full weight. If you want to do that then use 4x4 posts for the sides. There are some design ideas here that may help you out.
http://www.mistressdestiny.com/threads/ ... ox.426512/
- Heely111
- Posts: 44
- Joined: Fri Apr 02, 2010 2:48 pm
Re: Cockbox
Hello Stephanie_Stepsie,
you can look here. My cockbox works very well and it was built very quick.
Heely
www.shoesession.com/forum/viewtopic.php?f=14&t=31591
you can look here. My cockbox works very well and it was built very quick.
Heely
www.shoesession.com/forum/viewtopic.php?f=14&t=31591
-
- Posts: 679
- Joined: Fri Sep 01, 2017 6:30 am
- Contact:
Re: Cockbox
Thank you for the linkHeely111 wrote: ↑Thu Jun 28, 2018 8:30 am Hello Stephanie_Stepsie,
you can look here. My cockbox works very well and it was built very quick.
Heely
www.shoesession.com/forum/viewtopic.php?f=14&t=31591
Who is online
Users browsing this forum: bestshoefucker, eddieMAD and 98 guests